Seat Alhambra Key Problems
Seat's jumbo family MPV is among the top in its class when it comes to conserving resale value. With a new model on sale the Jumbo family MPV is better.
There are a myriad of reasons why the key fob could not function correctly, including dead battery damage to the receiver module, water issues or signal interference. This article will guide you through the steps necessary to make sure it works.
Water Damage
If your key fob for the seat alhambra can withstand an wash cycle or dip in the water or a pool, it is equipped with a waterproof chip. But don't do this often, as prolonged exposure to water increases the likelihood that the key fob will be damaged. If your key fob ceases to working after exposure to rain or clean tap water, remove the battery and wipe the electronic component using a towel. Let it dry completely before replacing the battery. If the key fob was exposed to salty or soapy water and salty water, it is recommended you clean the chip with isopropyl or electronic cleaner.
Faulty Receiver Module
If you've tried a new button cell battery and the key fob doesn't lock or unlock then it's likely the receiver module has been faulty. The positive side is that this is a fairly easy and cost-effective fix. You can just disconnect the 12 volt battery for just a few minutes (first take off the negative cable, then press the horn button a few times) to eliminate any remaining electric current, then reconnect it in reverse order e.g. Positive first followed by negative.
ESP Warning Light – If the ESP symbol is illuminated, this is normal. It means that you are driving on terrain that has poor traction. This could be due to snow, gravel or surface water. If the ESP light is always on, it means that there is a fault in the system. It can be detected by using an iCarsoft i908 seat OBD code reader kit. It will give you detailed information about the fault.
Dead Coin Battery
One of the most frequent reasons for the seat alhambra key to stop working is a dead coin battery. The key fob is powered by a small button-cell battery. It should be replaced with a brand new one that is identical in size, voltage and specifications as the original. When replacing the battery on the key fob remove the metal clips and make sure that the contacts of the key fob are clean and free of corrosion.
If the key fob was exposed to water (such as soapy or rain tap water), it is recommended that you remove and clean the chip using an electronic cleaner or isopropyl alcohol prior to installing a new battery. The chip may be permanently damaged by water. If the key fob still doesn't function after replacing the battery it may be necessary for you to replace the key fob.
Faulty Receiver Module
If your key fob has stopped working after replacing the battery but it didn't work, or suddenly stopped working the receiver module may have developed a problem. The receiver module is responsible for capturing the radio frequency signals that are sent by your remote key fob and converting them into electrical commands which are then processed by other modules within the car.
If the receiver module has developed a fault, it will not respond to any of the commands issued by your remote key fob. In this scenario the dealer will have to reprogramme the key fob, and also install an additional receiver.
The key fob is encased with rubber to prevent water from leaking into the electronic chip. If you submerge the key fob into salty or soapy water it could damage the chip. If seat leon key replacement does not work, you could try cleaning the chip using isopropyl or an electronic cleaner.
If the keys have been paired, but the receiver module isn't working You can try to restart all of the electronics on board by disconnecting the battery at 12 volts for few minutes. Connect the battery in reverse (negative cable to positive first). This will reset the onboard electronic circuits and restore their functionality.
Faulty electronic chip
The key fob contains an electronic chip that transmits a message to the receiver module each time the key is used. If the signal doesn't match the one the car has stored the immobilizer will be disabled and stop the vehicle from starting. If the key fob does not function and you are not able to reprogram it, it could be due to an incompatible microchip.
The chip inside the key fob is not permanent to the device and may need to be replaced to get it working again. This can be done by getting the key fob removed from its case, and using pins or needles to make contact with each metal retaining clip. If these are corroded or broken, you will require replacement to allow the remote control to function. Make sure that the replacement batteries are of the same size, voltage, and specifications as the original one.
Seat Alhambra is a popular and well-designed car, can have problems with certain parts or components. There have been reports of problems with the climate control system that is automatic. It is prone to malfunction and become stuck in a specific setting. The infotainment system could also fail and freeze the screens.